Home > Iphone 4 > Iphone 4 Charging Port Replacement

Iphone 4 Charging Port Replacement

Contents

Remove the top logic board shield There are 5 screws holding the logic board shield in place. A dry clean toothbrush usually works. Podcasts Contact iMore About iMore Android Central Connectedly CrackBerry iMore Windows Central Tesla Central VR Heads MrMobile DIY How to replace a broken iPhone 5 screen in under 10 minutes DIY After replacing the connector I only get the USB connection graphic in the upper right corner of the phone instead of the lightening bolt. his comment is here

The dongle does officially support my hardware and OS level. Plug the rubber gasket back into the mid-frame. Remove the vibrator assembly The vibrator assembly is only held down with a bit of adhesive. I see there are 4 tiny components on the cable, 2 per signal track. imp source

Iphone 4 Charging Port Replacement

What causes my iPhone to think that it's docked when it isn't? I'm presuming ones a resistor and the other a capacitor for some sort of contact debouncing? Install the new dock connector assembly Place the rubber gasket you removed from the old assembly onto the new one and now we're ready to install the new one. You may have left some on.

I had iOS 6 running on the iPhone 5 and the line out audio would not work. In this step, we'll replace the problem cable. Although a repair shop might suggest you replace the home button, this YouTuber offered a different solution.Plug a USB cable into your iPhone. Iphone 4 Charging Port Repair Cost what I found was a suggestion to enable the passcode feature to lock the phone so it was not able to pick up voice commands ( I wasn't giving) so far

So I use the plastic opening tool on the other side to remove really gently the battery, it was really really stucked with the glue... You may need to use a plastic opening tool to loosen the adhesive under the battery. Prithvij Xarwin 70,913 views 1:30 Top 10 Unknown Facts About iPhones - Duration: 6:33. However the JIS #000 also in the kit did fit quite well.

Just peel it back. Iphone 4 Dock Connector Replacement Loading... This morning, suddenly my home button was working again, for all of 5 minutes, before it went back to not working, and voice control going off on its own again. bfbogaert - 11/17/2012 Reply Use an #000 fine screw driver to remove two screws from iPhone 4s!

Iphone 4 Dock Connector

B King - 03/13/2011 Reply I successfully did this, however now my mic is not working unless I am on speaker or using my headphones... Podcasts Contact iMore About iMore Android Central Connectedly CrackBerry iMore Windows Central Tesla Central VR Heads MrMobile DIY How to replace a broken iPhone 5 screen in under 10 minutes DIY Iphone 4 Charging Port Replacement In this case, your home button's connectors may have been misaligned and would require professional repair. (Or, if you're willing to brave it, iFixit shows you how to DIY.)The good news Iphone 4 Dock Connector No Sound Why is this accessory not working on my iPhone, and how can I get it working?

Don't panic, restore or pay someone for a new iPhone Home Button. this content We can help you replace your battery too: How to replace the battery in an iPhone 4 What you need for a DIY GSM iPhone 4 dock connector replacement We recommend Not the easiest to check, but a possibility. misc - 11/10/2014 Reply When pressing the battery connector into the socket, the first time I pressed from bottom to top. Iphone 4s Dock Connector Replacement

The hardest part was being sure the outer pentalobe screws were actually turning and I wasn't stripping them. On Sale Now 2 Answers Filter by: Most Helpful Newest Oldest Chosen Solution Krayzee @krayzee Rep: 395 8 2 Posted: 11/28/2012 Options Permalink History what i would try is:- -first of I tried a lot of different techniques I read about on here (blowing, compressed air, cotton swab), but nothing worked for more than a few seconds. weblink To remove the battery, I do not recommend using the plastic pull tab.

anyone else have this problem? Iphone 4 Dock Connector Problems Remove this cable in the picture above using your pry tool. iFixit: Repair Manual Official App Free – Google Play Install Select a Language: 中文 日本語 Deutsch English Español Français Italiano Nederlands Português Русский язык Türkçe Machine translation Help Translate iFixit Close

It's probably in errno.h and strerror.h depending on how far they have gotten from their BSD roots (just add something like ELOWPWR and "This accessory has insufficient power for charging." respectively).

At 70 minutes the battery indicated 30% charge, and at that rate should be fully charged in under 4 hours. ryebread02 - 06/24/2011 Reply Definitely agree on the moisture sensor. Hope this helps someone. Dock Connector Iphone Once the top left is free, move over to the top right corner and repeat.

May 18, 2012 1:13 AM Helpful (0) Reply options Link to this post by iOSgaga, iOSgaga Jan 5, 2013 7:42 PM in response to seanbperiod Level 1 (0 points) Jan 5, share|improve this answer edited Jul 18 '13 at 10:46 bmike♦ 117k38203446 answered Jul 17 '13 at 13:36 Anthony 1 What might "messing around with the vibrate settings" entail if Using a very small amount of your cleaning agent, and keeping the phone upright so any drips fall out, and not into the phone, lightly brush or wipe the dock connector, check over here Thanks.

It appears that there is a software setpoint for current (or power since the voltage is supposed to be the fixed) below which this state is triggered. Jun 5, 2013 8:49 PM Helpful (0) Reply options Link to this post by Ryan Haverstock, Ryan Haverstock Jun 23, 2013 2:44 AM in response to seanbperiod Level 1 (0 points) Hit it If this doesn't work, then the issue could still be a physical obstruction, although it may be beyond the dock connector and more internal. TODO: Get a cheap charger from the Dollar Tree, expose the wire and use a potentiometer and ammeter to determine an approximate current threshold that triggers the message inoperable charging state.

After button replacement, home button worked a bit and now entirely unresponsive. (using soft home button in accessibility). It should come up easily so pry up gently.You'll notice that it is wrapped around a metal clip. Note the folding of the cable and the positioning of the rubber microphone cover for reassembly. During reassembly, we recommend you replace the 5-point screws with equivalent Phillips screws.

Why is で used here? Note 2 If your device is failing to charge, or will only charge from a certain cable or dock, then the same fix potentially applies. It slips over your head and provides 10x magnification. ( You can find them on Amazon). step 24.

Just make sure you are careful not to bend it. jenkinschristopher - 04/14/2012 Reply I was able to replace the charging dock fairly easily BUT I skipped some steps that seemed unnecessary: (1) I did NOT remove the battery. Be sure you are prying up on the retaining flap, not the socket itself. Took it apart again, removed and reinstalled the dock connector paying special attention to the mic.