Home > Iphone 3gs > Iphone 3gs Side Buttons Not Working

Iphone 3gs Side Buttons Not Working

kristymic - 09/02/2009 Reply Quote from kristymic: I bought my black iPhone a full housing white cover off ebay. I added a note so that people are aware that the colors may be reversed. I needed this because, I have passed the stage of squeezing. facar04 24,255 views 3:06 iPhone 4/4s Volume button problem fix - Duration: 2:15. http://virtualthought.net/iphone-3gs/iphone-3gs-power-volume-buttons-not-working.html

Is it possible I've damaged the aerial in the process? I had to replace the Headphone Jack Assembly which contains the power button. So using a sharp cutter, I cut a bit hole. Sure others here would love to know as well.

Model A1303 / 16 or 32 GB capacity / black or white plastic back. However the Home button will not work until the front panel is back in position, because the electrical connection is done by a pair of touch contacts which only work when MarySC - 07/31/2011 Reply When re-inserting the #3 connector how much force does it take to get the connector fully inserted? Mathew Taylor - 01/18/2011 Reply When re-installing the mother board ensure that all of the previoulsly diconnected connector cables are out of the way and do not become trapped by the

Be very careful when assembling not to force the connector down; It should click actually quite easily once it's placed properly. marmalade - 10/22/2009 Reply How on earth do I get the black ribbon cable back into its connector??? Remove the vibrator from the rear panel. My seems to keep dropping out and the ear speaker is not working.

iPhone just shows apple log and it dissapears after 5 seconds. It was very difficult to get the camera back in place. February 1 by trking46 Neither pressing or blowing worked but this did. https://www.ifixit.com/Answers/View/51328/iPhone+3GS+Silent+switch+is+not+working Looking at the picture makes this step brain dead simple, but if you were using another iPhone to read the directions it would be easy to miss.

Add a comment Add a comment Add Comment 1024 Step 22 Edit Carefully lift the headphone jack assembly out of the iPhone. Was this answer helpful? Without a spacer, the button may not protrude enough to be depressed. However, the half on the motherboard is tiny and soldered on.

you can try a bit of fix with something to make the toggle stay in it's groove or replace the part and know that the problem is solved. you could check here Make surre The spudger is inserted underneath that rubber piece. I have cleaned the area and still have this problem. So Here's what I did with success: I lightly moistened a cotton ball with regular rubbing alcohol and then gently passed it over the on/off button (upper right top) several times

The button goes into the back of the phone with the 'long side' of the swing faces the back of the phone. this content Quote from Vishal Vaidya: Is there a way of replacing the connector? kaseyrayne 107,659 views 4:17 iphone 4 no volume bar fix - Duration: 4:53. Remove the volume button.

I believe it's one piece when you go to replace it. The power button, headphone jack, volume rocker, and vibrate switch were all accessible with the battery still in place. Being flush it's switch it on and off. weblink Lenore - 01/31/2010 Reply Quote from Lenore: When reversing directions for reassembly, the logic board needs to be clipped into the clips on the side. ++ Although I would say "needs

Cancel Prashant Sharma Rep: 1 Posted: 06/19/2014 Options Permalink History Dear friends , pressing the handset near the earpiece works for me , thanks Mark ,the cause of the problem for Yesterday I tried switching it and it worked, but it was just that time, cause immediately stopped working again. All very odd.

It's mentioned in step 12 of many of the guides.

Luckily, you can remove just the camera enclosure from the 3GS and transplant it to the 3G. Tapping Volume down a few times may actually start your button working again.
Upgrade If you’re not running the latest iOS, try upgrading your software. The mute switch assembly screws should be tightened with the switch in the off position. Turbo Fredriksson - 04/02/2010 Reply Quote from cliffcurtis: if anyone knows where to buy a replacement flip tab, that'd be cool too :) http://www.earth2k.com/fpc-ribbon/ http://cgi.ebay.com/ws/eBayISAPI.dll?Vie...

THANKS! Thank for the help. There is a small plastic spacer adhered to the inside of button which may come off with cleaning. check over here zeke - 09/27/2010 Reply There are no delicate parts below the battery so you can push the spudger under the battery without damaging anything.

JavaScript seems to be disabled in your browser. I had one scary moment where my screen would not turn on but a Hard Reset on the phone fixed it. Reply Henry W. would that be the reason that the iPhone would not start even though the ribbon is in the connector and fastened secured with the white plastic tab is down.

It was removed and set aside many steps ago. Alessandro AlexPi - 11/13/2009 Reply Well, I took the chance and the LCD broke on this step. It works fine when it is switched off (sound on) but does not always work when I flip it to silent mode. Cancel Deepti Ghadiyaram Rep: 13 1 Posted: 06/25/2012 Options Permalink History For a hard reboot, keep pressing the power button and the menu button ( the big round one) for several

cliffcurtis - 08/06/2009 Reply I bought my black iPhone a full housing white cover off ebay. For the iPhone 5S, you can visit our iPhone 5S Volume Repair Service. Currently my iPhone has become an iPod! In this case you would slide the ribbon cable towards the screen until it is removed.

Go to Settings>General>Accessibility and turn on Assistive Touch. Yes No Voted Undo Score 1 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?