Home > Iphone 3gs > Iphone 3gs Proximity Sensor Not Working

Iphone 3gs Proximity Sensor Not Working

I have verified that: • The Iphone 3G and 3GS proximity sensors work the same and have about a 2 inch range. Apple needs to fix the problem. Use extreme care and caution when performing a repair on any device. Soon after, I realized that the proximity sensor was not working - the screen would remain on and active during calls while I held the phone to my face. his comment is here

How can I check it? 5Why is the top button on my iPhone 3Gs not working consistently?2iPhone calendar alerts are not muted when vibrate switch is on1my wife just got an Bruce IPhone4 running iOS 5 with invisível shield. benben20 83,638 views 5:33 Fix Your iPhone Proximity Sensor During Calls - iOS Vlog 220 - Duration: 2:25. Has anyone determined a solution for this?

benben20 23,277 views 8:05 How to fix the backlight in a 3GS iPhone with dim screen. From that point it would only activate when I move the paper to one inch away and not 2 inches any longer. I have done hard resets, turned the phone off completely, waited 10 minutes and then rebooted, but the battery drain is still the same. I normally only push the sleep button when I am talking to my friend with my earbuds in.

Reassemble your iPhone Once you've replaced the proximity sensor cable, you'll just need to reassemble your iPhone by following these directions in exact reverse order. earpiece. The trip point for the proximity sensor is always at around 2 inches for the 3G and 3GS. • The Iphone 4 proximity sensor works differently than the 3G and 3GS. Is it an actual sensor issue?

Resetting setting, restore to 'new iPhone' doesn't do anything. I'm prepared to restore it if that's the only possible solution, of course, and I'd have to at any rate in order to receive service for it. Staying on track when learning theory vs learning to play Isn't the BBC being extremely irresponsible in describing how to authenticate an account-related email? https://www.ifixit.com/Answers/View/56282/How+can+I+repair+a+proximity+sensor iPhoneRepairMia 9,656 views 3:22 How to replace an iPhone 3G 3GS proximity sensor cable - Duration: 7:27.

but the photo quality comes out a bit low and unusable in my onion,the whole process to do things with it is daunting as well! Fender Wow that was indepth. Cancel Add your answer Gabriel will be eternally grateful. The touching of the screen does not always turn on this screen either.Another thing is that ios4 drains my battery much quicker than it did when it was on 3.1.3.

Not the true network readings.

I take it the problem continued after you removed the OS changes you made, is that right? –Matthew Frederick Jan 3 '11 at 6:57 1 The idea is to seek Instead of charging them $50 bucks to replace it, I did this fix for free. I come on again in a second or 2.

If you do run into problems, make sure to check out our DIY and mod forums below. this content It is easier than replacing just the sensors. At first, as I triggered the display (during my simulated call) I noticed that the brightness level of the display would change as the display reactivated itself. If nothings helping you could have randomly just got a bad phone.

But if i read this, i think Im not alone with the shit, every phone call i activate the damn speaker. i did the setet all and soft and nothing what shoukd i do???? I betcha if the tint was removed where the sproc is the issue would disappear. http://virtualthought.net/iphone-3gs/iphone-3gs-ambient-light-sensor-not-working.html uncletone99 139,458 views 5:33 iphone 3gs / 3g connector 3 FPC repair - Duration: 8:59.

Yes No Voted Undo Score 1 Cancel Comments: @hectordtruong: I am unsure about how securely the sensor cable fit back in, but now that you mention the digitizer, I did notice Use your #00 screwdriver to remove the one screw in the top right that's holding down the flex cable and your LCD. (If you removed your LCD, you will have already Said it wasn't a fault with the phone and did not replace the phones.

Tyephone 36,648 views 3:25 Maldito sensor de presença do iPhone 4 - Duration: 1:53.

Yes No Voted Undo Score 2 Cancel Comments: Hi tyler, did the proximity repair require you to remove the digitiser from the frame? Go Cell Phone Repair 376,422 views 4:21 iPhone 3Gs backlight dim LCD 6R8 coil inductor fix repair - Duration: 8:37. Did you guys find a fix? They are one in the same.

So, people who are used to holding the phone over their shoulders are the ones who have the problem mostly. In comparison to the 3gs?? You got a few billion dollars of inventory already on the streets, and rather than hold production or stop sales and fix the problems like a good manufacture, they continue to check over here Faris What are you talking about Davissi??

I could remove the paper for a few seconds and my Iphone 4 proximity sensor would start detecting again at two inches. iPhone 3GS Proximity Sensor Ribbon Replacement Guide iPhone 3GS Proximity Sensor Ribbon Replacement Difficulty: Moderate Was this answer helpful? Only works when light is completely blocked with a black surface.Glad to see this because now it is definitely marked as a software glitch. That did not work, however, and the proximity sensor is still broken.

Now, I barely get a full day out of it when most of the time, it is not even being used. Underneath these cables you'll see one other labeled as cable 3. DirectFix 929,407 views 8:58 iphone 3gs / 3g connector 3 FPC repair - Duration: 8:59. An infinite chain of theories Plural acronym verb form: "PGCs stand for" vs. "PGCs stands for" Arduino IDE not recognizing that .c file is .cpp Which of the items I had

Preview my answer Post my answer View Statistics: Past 24 Hours: 0 Past 7 Days: 0 Past 30 Days: 7 All Time: 3,285 22,584 Free Manuals 89,391 Solutions 6,841 Devices iFixit iPhoneRepairMia 200,353 views 4:11 Official iPhone 3G / 3GS Screen / Digitizer Repair and Replacement Video - iCracked.com - Duration: 17:03. The 3GS is still a great phone, much better than the 4 at present. Symptoms Your earpiece speaker cuts in and out or you can't hear unless you have speakerphone activated (this can also be caused by a broken earpiece speaker) Your ambient light sensor

Replace the proximity sensor cable You'll notice that the proximity sensor cable is attached with some adhesive to the metal clip that holds it in place.