It should be labeled with a sticker saying "5" with an arrow pointing to a connector. Jessi Darklighter - 11/07/2013 Reply Try to lever the screw's head with a flat screwdriver or a knife, so you can force it outwards while you screw it lose. It needs to flip upwards towards the ribbon cable. So we'll call these the 'short side' and 'long side'. http://virtualthought.net/iphone-3gs/iphone-3gs-side-buttons-not-working.html
Liam George - 05/01/2010 Reply While disassembling, the screw in the far right corner should be separated from the other screws. How long is the "slightly longer" screw on the far right? Inicia sesión para añadir este vídeo a la lista Ver más tarde. Only by pulling out? 2. browse this site
Quote from johnhart: ++ Although I would say "needs to be slipped under the clips on the side". Se podrá valorar cuando se haya alquilado el vídeo. Iniciar sesión 73 Cargando... This is an easy fix.
A tip: to handle the screws, very small, I used a pair of tweezers for eyebrows wrapped in double sided adhesive tape. Ribbon #2: Runs the digitizer 3. Iniciar sesión 45 25 ¿No te gusta este vídeo? jargogle - 09/15/2011 Reply Agree with this comment.
Hope it helps Categoría Formación Licencia Licencia de YouTube estándar Mostrar más Mostrar menos Cargando... I've tried every combination and am staggered that i can't find a single resource online that covers this. taylor431 - 12/01/2009 Reply How could the LCD break on this step? https://www.ifixit.com/Answers/View/45709/Headphone+jack,+power+button,+volume+and+mute+not+working Cerrar Más información View this message in English Estás viendo YouTube en Español (España).
Thank you 03/04/2011 by Rakesh Mora The power button on the new ribbon that you installed isn't working? Everything went fine until I put it together and tried to start it up. Anuncio Reproducción automática Si la reproducción automática está habilitada, se reproducirá automáticamente un vídeo a continuación. powered by Olark live chat software Web Toolbar by Wibiya Recordármelo más tarde Revisar Recordatorio de privacidad de YouTube, una empresa de Google Saltar navegación ESSubirIniciar sesiónBuscar Cargando...
Be VERY careful this does not snag on the side of the case when prying up the logic board; it breaks easily. http://iresq.com/apple-repair-news/solutions-iphone-volume-button-working/ If your replacement battery already includes an adhesive backing, you're all set. While everything inside was dry as a bone, I never did remove the battery since the adhesive was so strong. kristymic - 09/02/2009 Reply Quote from kristymic: I bought my black iPhone a full housing white cover off ebay.
Conclusion To reassemble your device, follow these instructions in reverse order. this content That is because the golden clip nearby the "do not remove sticker". PAZOTIVE TECH REVIEWS 444.031 visualizaciones 6:01 iPhone 3G and 3GS Complete Strip and Re-Build Repair Guide - www.AppleiPodParts.com - Duración: 39:03. It's still possible to get all the screws back in with the logic board above the clips (trust me), but it's a serious barnus because the SIM card holder won't fit
Try "parallel and aligned". When the center of the circle in the ribbon is exactly over the center of the connector on the board the respective circles of the connector halves are CONCENTRIC and properly Inicia sesión para que tengamos en cuenta tu opinión. weblink iCracked 318.983 visualizaciones 16:50 iPhone Volume Fix Guaranteed - Duración: 3:17.
When reinserting the logic board, there is a tab in the top edge of the rear shell case that the edge of the logic board goes under. Esta función no está disponible en este momento. Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Without this "comfortable" fit, you won't be able to get the SIM in.
JanWillem - 11/03/2011 Reply I think that this is where the problem is. Cor Berkelaar - 03/27/2010 Reply Quote from Cor Berkelaar: How on earth do I get the black ribbon cable back into its connector??? Be sure it doesn't fly out or fall into the phone workings. check over here Evagoras Mandrides 65.855 visualizaciones 2:15 Cargando más sugerencias...
iluxan - 08/17/2011 I think the steps to replace the connectors 6 & 7 should be emphasized because of the size/fragility of the connectors. Cor, You have to slide the little bar on the connector away from the body of the connector before you can insert the ribbon cable into it. iggypop - 04/24/2010 Reply Power button is a little funny. All seems good.
satsho - 03/16/2012 I agree with the others that cable 6 and 7 are very fragile and can be difficult to reattach. PCification 41.715 visualizaciones 3:37 iPhone 3G and 3GS Battery Replacement Guide - Fix it Yourself! - Duración: 15:00. Tapping Volume down a few times may actually start your button working again. Upgrade If you’re not running the latest iOS, try upgrading your software. I found the spudger far too weak to even attempt the removal of the battery.
Technickal28 - 05/28/2010 Reply For me, two questions are not answered yet in this step: It is only possible to buy a flex cable without the microswitch and the metal housing germanperezsalva - 07/18/2013 Reply When I put the new battery in, it was a smidge too far toward the bottom. I will try and let you know. expect it to vibrate as if you toggled the mute button!
© Copyright 2017 virtualthought.net. All rights reserved.