Home > Iphone 3g > Iphone 3g Screen Not Working After Repair

Iphone 3g Screen Not Working After Repair

Was this answer helpful? iPad 2 here 10/29/2012 by Daniel Schuchter Yeah, one slight major difference. I've restored the phone and it completes it goes into DFU mode and it vibrates at times but there's no picture. It wouldn't turn on, didn't vibrate when i put it on silent and iTunes wouldn't recognise it was plugged in! his comment is here

the display on but showed "white backlight". When I put the charger in I heard the sound... On Sale Now 16 Answers Filter by: Most Helpful Newest Oldest Chosen Solution pollytintop @pollytintop Rep: 70.9k 318 89 120 Posted: 08/26/2010 Options Permalink History if the screen is black completely Battery is charged and working fine. https://www.ifixit.com/Answers/View/47721/Screen+not+responding+after+replacement.

Cancel 3 Answers Filter by: Most Helpful Newest Oldest Most Helpful Answer QEII Student IT Rep: 4.5k 25 29 4 Posted: 02/06/2010 Options Permalink History Well it does seem that the Yes No Voted Undo Score 0 Cancel Comments: Je suis utilisant un navigateur internet traducteur j'espère donc ce sort correctement! The motherboard does indeed get "tricked" into thinking the LCD is on when it is not.

We gotta get the word out!! Model A1241 / 8 or 16 GB capacity / black or white plastic back. These are sometimes essential for keeping the #3 connector down and steady. This helps when I get a stubborn phone.

I cant do the sensitivity increase because the screen doesnt work at all. This feature is not available right now. All rights reserved. Jan 10, 2010 9:59 PM Helpful (0) Reply options Link to this post by Brian965, Brian965 Jan 11, 2010 7:25 PM in response to modular747 Level 1 (0 points) Jan 11,

Please try again later. etc. Possible solution: hold power and home button together to reset the phone. Everything seems right, I checked and rechecked connectors 1, 2, and 3 to make sure they're all placed correctly.

When the iphone 4 was new alot of the replacement screens were garbage, and I think it ws the same with the iPads. page No damage at all can be seen, I bought a new back housing and after putting it all back together this happened... of course... Maybe the battery was disconnected long enough to shut the system down and let the last screen hook up take?

iCracked 200,185 views 17:03 iPhone 3G and 3GS Complete Strip and Re-Build Repair Guide - www.AppleiPodParts.com - Duration: 39:03. this content Cancel Most Helpful Answer Steve Parkhurst Rep: 109 3 Posted: 02/24/2011 Options Permalink History I have had this problem several times on the same phone, I let it sit for 2-3 Hard Reset 5. Cancel Richie Rep: 1 Posted: 05/20/2014 Options Permalink History I have repaired an ipad 2....I put it all back togetherand now the digitizer wont respond.

Now after replacing the digitizer, the touch screen will not respond... Was this answer helpful? When I clip in the bottom...... weblink I used a randon piece of ribbon cable to do the same for the LCD ribbon cable.

The digitizer cable plug in the iphone has a small foam pad on the top of it, so I don't know if mylar tape is going to be effective. What black clips are they talking about and just like you stated, "these guys are crazy... Im leaning toward A.

After reassembly this resulted in a black screen.

Does the screen light up? Good luck! I dont recommend it but with the plastic tool move the pins in slightly or put a pieces of tape to hold it on. I think 1 and 2 snap, 3 is a ribbon cable that requires you to loosen the small clip to remove it.

folow itunes instruction until the system restart on you computer, if you can see any instruction on your iphone display, then everything will be fine; 4. I followed the instructions extremely well, and on the last step, I went to clip the digitizer into it's spot when low and behold the little plastic clip broke off also. I have tried resetting it Via Home+power. http://virtualthought.net/iphone-3g/iphone-3g-new-digitizer-not-working.html [email protected] January 23 by Donna Kaminsky Show 5 more comments Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?

Cancel Randystrin Rep: 1 Posted: 11/09/2013 Options Permalink History I too broke the clips when replacing the screen on my ipad 3. I don't even know if the new battery has taken a charge. I covered the entire back including the little dotted white line. My biggest problem lately is getting good parts on ebay.

View the answer I have this problem too Subscribed to new answers Is this a good question? notting react wen i hold the power botton. But the screen is still black and the touchscreen doesn't appear to be working (before i replaced the screen the touchscreen was working fine and i could answer calls etc.) From Apple disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site.

Answered!