Home > How To > High Pressure Sodium Lights Troubleshooting

High Pressure Sodium Lights Troubleshooting

Contents

Yükleniyor... Found the ballast. I'm fairly sure these internal parts are fairly inexpensive and can be purchased at a local electrical supply center. The desire for green energy is just gaining ground in the United States, and isn’t limited to the HVAC industry. have a peek here

KnisleyLighting Consultant165 Articles EMAIL Tweet Comments 0 Understanding the characteristics of fluorescent and HID lamps makes it easier to recognize problems and simplifies corrective maintenance. bleupitbudz, Nov 18, 2010 #2 Dutch Pimp Up in Smoke after you get done monkeying around with the electronics...you should test it in a safe area, for several days...(not the attic) This condition, known as lamp rectification, will cause a reduction in ballast life if it continues. High pressure sodium lamps require approximately one minute to cool before restriking.

High Pressure Sodium Lights Troubleshooting

In most cases this phrase often refers to electronic ballasts operating HID lamps. NOTE: We DO NOT recommend dimming lamps because it dramatically changes the spectral output required for quality plant growth. On the other hand, a series sequence ballast operates lamps in series (meaning if one lamp fails the other will fail or glow dimly). A note of caution: Hybrid magnetic ballasts (developed as a bridge technology between magnetic and fully solid-state electronic ballasts for 4-ft lamps) have components that cut off power to lamp cathode

How to Repair an HID Ballast Consider trying out these simple repairs for an HID ballast before you scrap the system for a new one. You can test the ballast capacitor with a suitable analog-type ohmmeter, set at a high resistance scale. Ekle Bu videoyu daha sonra tekrar izlemek mi istiyorsunuz? How To Test A Metal Halide Ballast With A Multimeter Reliability.

Sometimes you'll find leads without the insulation. The capacitor and the ingnitor can be purchased online for about $10.00 a piece. ATSLLCUSA 141.835 görüntüleme 25:03 How to Diagnose and Repair Your Ballast Cheeply and With Better Parts - Süre: 7:00. Read More Here Confirmation of a partially failed capacitor can be made by measuring it with a capacitance meter ($20 to $80).

More350Power 9.232 görüntüleme 7:16 High Pressure Sodium and Metal Halide: What's the Difference? - Süre: 4:18. Hps Capacitor Replace capacitor if necessary. Troubleshooting Lamp/Ballast Compatibility Lamp/ballast compatibility (LBC) is a phrase used to describe the working relationship between a ballast and a HID lamp. HID ballasts.

How To Test Ballast Ignitor

Check for loose connection. http://boards.cannabis.com/threads/600w-hps-ballast-problem.192513/ Safety. High Pressure Sodium Lights Troubleshooting still soft and the component wiring is still legible. How To Test A High Pressure Sodium Bulb If during the test you find the fuse blown, then you know that there is a short in the ballast.

Shut off the main power and unplug the ballast. For that reason, its insulation material can break down and cause a short in the core/coil windings. When installing lamps with exposed bi-pins, make sure the positioning guide (an embossed mark on the metal end cap) is opposite the entrance slot of the lampholder before inserting. bleupitbudz, Nov 19, 2010 #4 bleupitbudz Registered Removal and installation of HPS ignitor Picked up the new ignitor from my local hydroponic shop. How To Tell If A High Pressure Sodium Bulb Is Bad

High Lamp Operating Voltage/Low Open Circuit Ballast Voltage Measure lamp operating voltage. d. When this point is reached, the lamp will exhibit cycling on and off characteristics. Check This Out You can change this preference below.

Keep in mind any wattage or ampere reading taken on the branch circuit will reflect this change of status condition. Hps Ignitor How It Works Join the Discussion on EC&M Talk Hot TopicsCommentsNew Topics AFCI 2 last reply by Paul Abernathy in General Electrical Talk Discussion Hazardous Location Class 1 Div 2 On A Building 2 Heavy premature end darkening (usually at only one end) is a good indication that one cathode is not properly heated and, therefore, the heater circuit is incomplete.

Wrong Lamp Color Check etch on lamps which appear different to see that they are actually the same color.

Incorrect Ballast Output Check ballast output to determine if it conforms to lamp requirements. Replace components as required. 9. After Hours Tv & Pc repair 411.649 görüntüleme 4:22 Basic Electronic Components and their Symbols and Connections - Süre: 35:25. Difference Between Ballast And Ignitor Reflector Problem Reflector design may refocus radiant energy directly on the arc tube or other parts of the lamp causing overheating.

We’ve Got You Covered....More BROWSE ALL VIDEOS Sponsored by Advertisement EC&M Learning Center Understanding the 2014 NEC, Volume 1 (Articles 90 to 480) Thisresource has proven itself in the field and Establish maintenance program. 5. Similar Threads Need Help Wiring Hps Ballast wab555, Jun 25, 2014, in forum: Lighting Replies: 9 Views: 1,829 4fingerliddays Jul 1, 2014 Ballast not working, need some ideas. If voltage and current do not stabilize in five to ten minutes warm-up time, ballast output is incorrect and adjustment should be made.

You can classify most of these lamp types under the heading of rapid-start lamps. Provide voltage regulators. Learn more You're viewing YouTube in Turkish. According to Mr.

rhapsodyrcks Registered User Joined: Apr 17, 2011 Messages: 8,164 Likes Received: 1,951 #2 rhapsodyrcks, Jan 15, 2012 Id call up a hydro store and talk to them. The lamp is a receiver of power. Under certain conditions new lamps may "cycle". These, in turn, relate to maintenance/troubleshooting needs.

Comments Ballast Wiring Tips and Tricks You may also like: How to Test a Light Ballast Make sure your electrical ballast is working properly with a simple test. Remember, though a ballast starts a lamp, this does not necessarily mean the ballast is functioning properly. High Restrike Voltage (Metal Halide Only) This condition is peculiar to the metal halide lamp. Right away the knowledgeable employee told me it was the ignitor.

MrDollarproductions 1.002.950 görüntüleme 4:30 LET THERE BE LIGHT - High Pressure Sodium Light Test - Süre: 7:16. Here's what you should look for in a lamp's appearance: Non-starting; On-and-off cycling; Extra-bright-light output; and Low-light output. If the test lamp does not light, the ballast has most likely reached its end of life. 15. Now you will need to turn the system on.

I'll be putting it back and monitoring regularly. Back to top PROBLEM 6—LAMP LIGHT OUTPUT LOW POSSIBLE CAUSE CORRECTIVE ACTION 1. TANKJR, Dec 10, 2010 #7 CakeCakeCake Registered Thanks for posting. The lamp just sits there and takes what the ballast provides.

Mismatched Ignitor Verify that the ballast and ignitor are matched according to the specifications. Replace lamp. 2. All Rights Reserved.