Home > Hot Tub > Spa Blower Motor Replacement

Spa Blower Motor Replacement

Contents

curtzblues 5,067 views 2:45 Hot Tub Broken Pump Union Emergency Repair The Spa Guy How To Series - Duration: 4:01. Tweet Share53 Pin110 Share34Shares 197 This Is The Last Hot Tub Manual You Will Ever Need You'll save at least $100 off the bat with this easy-to-follow digital handbook. Not sure what to try next. Tweet Share2 Pin Share7Shares 9 This Is The Last Hot Tub Manual You Will Ever Need You'll save at least $100 off the bat with this easy-to-follow digital handbook. have a peek at this web-site

See if you hear a click. Welcome, Guest. Heat Works but Tub Does Not Reach 104 Degrees Be sure thermostat is turned all the way up and that the equipment area is well ventilated. If it's stuck, use a small screwdriver to pry it out gently. http://www.doityourself.com/stry/troubleshooting-hot-tub-blower-problems

Spa Blower Motor Replacement

If power is coming through timer, check the Black wire at the back of the pump for power. A thread file makes shaft repair very quick and accurate with little effort.) When replacing a pump seal, wet the impeller shaft a little with water to make sliding it on Electronic temperature controls are generally more reliable.

Be sure the thermostat is turned all the way to "Hi" before looking for voltage. This can happen if during shipment the equipment is stored in a room or truck that gets very hot inside, in which case the hi limit will trip and engage the Please try again later. Silencer Air Blower Troubleshooting I need to replace it but until it warms up here I can't risk a freeze.

I've never seen this before and just had to share. Hot Tub Blower Works But No Bubbles All rights reserved. Correct if necessary as described in #2. Contactors Thermostats - Mechanical vs.

This could be due to high amperage (such as in a heater) or due to a GFCI protected circuit needing control over a non-GFCI protected circuit. What Does A Spa Blower Do Matt Giovanisci You might have air in the lines. Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Heater Problems Heater Failure - Due to Water Flow Are the ball valves open?

Hot Tub Blower Works But No Bubbles

Professional help is normally required if replacing the pump does not remedy the problem. Test and balance water. Spa Blower Motor Replacement Thermostat sensing bulb not applied: Make sure the sensing bulb is applied to the manifold under the heat tape (older models) or inside a thermowell if provided. How Does A Spa Blower Work a) consists of a household vacuum cleaner motor (fig.

Heater element? Professional help is required if filling the tub does not solve the problem. When the pack leaves the factory, the timer switch controlling the low speed is open such that the low speed pump will not come on. Filters: Diatomaceous Earth Filters are made of grids of extremely fine mesh that are coated with diatomaceous earth. Hot Tub Blower Trips Breaker

Your tech support department was first-rate, more than helpful with my repair questions." Mort Sorenson Fair Oaks, CA Get the LATEST DEALS: Sign UpTUB TIMES Newsletter Products Spa Showroom Spa When changing an impeller, it is best to examine the motor shaft and remove any build up of rust that might have occurred during the life of the pump. Sign in 12 0 Don't like this video? http://virtualthought.net/hot-tub/hot-tub-blower-not-working.html Turn pump on.

You would need to replace it. Hot Tub Blower Making Noise When purchasing a replacement part, make sure you buy the one that matches your hot tub and its electrical requirements exactly. I tried to restart it but it wouldn't work for long it would go into watchdog mode.

What’s wrong?” This is a common question and the answer is usually as simple as twisting the face of the jet to allow water flow.

Frozen water in the Pumps? Polaris 1-516-03 Metal Spa Blower, 1-1/2-Horsepower 240-Volt List Price: $214.17 Price: $166.99 You Save: $47.18 (22%) Buy Now On Amazon A Little Info on Air Blowers Before you start the repair, Since the check valve contains small parts that may eventually fail, this inexpensive part is a cheap insurance policy against water intrusion. Spa Blower Check Valve Tighten the motor bolts carefully and once all are tight, check once more to make sure the shaft is centered.

Be sure to reuse the same nuts if you remove them. That is, if the tripper in front of the arrow is pushed in, and the next several trippers are also pushed in, turning the bypass to have the low speed pump Everything froze. Re: Blower motor won't come on « Reply #1 on: April 18, 2007, 07:51:01 PM » There is a fuse on the board for the blower on that spa if I

Then also check to make sure the pack it is connected to is wired appropriately for this pump to be used. (Some replacements are improperly applied in the field.) Once you About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! It did come on at the beginning of every filtration cycle, and it was used occasionally for people wanting ultra strong jet power (not me). Water leaking into the pack can collect and cause this as well.

Rating is available when the video has been rented. The contamination could cause premature failure of the seal. In the other, a channel cavity is adhered to the shell of your hot tub which has holes drilled allowing the air to pass to the water. Most now have electronic temperature controls (called a Thermistor) available with the spa-side control heads.