Home > Hot Tub > Hot Tub Pump Wont Turn On

Hot Tub Pump Wont Turn On

Contents

Have tried everything to fix it. Arrows for morphisms of exact sequences My cat sat on my laptop, now the right side of my keyboard types the wrong characters How to add a phrase-less key to ssh If the plunger gets stuck on the hole, turn the spa off and remove it. Maybe it looks a little something like this: [attachment=0:12fija01]air relief.JPG[/attachment:12fija01] The red arrows point to unions, the blue arrow points to where there may or may not be a drain plug. have a peek at this web-site

Sign in 11 Loading... Does it hum or vibrate when you turn on your jets? Solution: If hot tub is under-filled, add water to the normal fill line. Fuse?

Hot Tub Pump Wont Turn On

Once the water gets going put the filter back in place and turn the pump on high to purge the remaining air. That's the one that was replaced first. Look inside the inlet to make sure nothing is inside blocking the flow of water. 11. Dry-rotted, out of position, or possibly loose, along with loose screws around the face of the pump.

Lab colleague uses cracked software. I recently drained and filled my hot tub. Newer, electronic air switches can be tested with a multi-meter, to see that power is passing through, on both sides of the switch. 2 Speed Spa Pump Troubleshooting If the air is not purged within 2-3 minutes, turn the spa off, let the pump cool off, and try again.

Bill Walker I just bought a Viking Spas Legacy 2 hot tub about a month ago. Important note: This is a dry test and and even if it tests OK on the bench, when you add the extra load of the water into the pump with an Turn the spa off, clamp the lid in place, spa back on, pump on high and you should be in business. Most hot tubs come with adjustable jets that can be turned down for less water flow, or closed completely.

enlarge 15. Hot Tub Jets Not Working On One Side If an AC motor like this won't start, there's a good chance it's the start capacitor. Common Problems Now that we all understand at least a little bit about how a pump actually works, let’s take a look at many of the most common problems you just If not, the Circuit Breaker may be tripped.

Hot Tub Motor Won't Start

All up in your equipment.

So I check the fuses, looked at the high limit probe. Hot Tub Pump Wont Turn On I need to replace it but until it warms up here I can't risk a freeze. Hot Tub Circulation Pump Not Working Go back to your union/drain plug and loosen it again.

Got it? http://virtualthought.net/hot-tub/hot-tub-jets-won-39-t-turn-on.html Up next How to Fix an Air Lock in Your Spa : Pools & Spas - Duration: 3:08. All up in your equipment. Shut off the breaker. Hot Tub Pump Just Hums

Loading... Repeat this process, using the lid like a plunger until water starts to come up at you from the filter housing. Second, if your tub is full, and still no water runs out, look for any closed valves before or after the pump. http://virtualthought.net/hot-tub/hot-tub-circulation-pump-repair.html DISCONNECT THE POWER AT THE GFCI SWITCH AND/OR THE MAIN PANEL CIRCUT BREAKER or FUSE BEFORE INSPECTING OR INSTALLING SPA PARTS.

Do they affect credit score? Hot Tub Air Lock Symptoms Do not attempt to perform electrical repairs unless you are qualified. Thanks, Marcu Reply With Quote 05-15-2016,11:02 AM #16 pooldv View Profile View Forum Posts View Articles Mod Squad Join Date Aug 2012 Location DFW, TX Posts 16,248 Re: Jets not

Sometimes that is enough to get water seeping into any crevices and the priming the next day may go better.  Otherwise, opening the union slightly may help get air out.

Thanks again!!! Please try again later. My Hot Tub Won’t Heat Sometimes a heating problem is as simple as replacing a heater element, however sometimes the problem can be caused by another component. Hot Tub Pump Making Noise I make a lot of money every year around this time from people who are unable to diagnose and fix air locks, so hopefully this will reach a few in need!

To determine which component is causing the problem, unplug the components one at a time and turn the breaker on. Many parts such as the jets, the skimmer basket or even the impeller could be clogged by dirt and debris. The spa is at a temperature above 108° F. http://virtualthought.net/hot-tub/hot-tub-circulation-pump-not-working.html Matt Giovanisci At this point I would just call someone.

With power off, manually operate the switch, looking for something loose, broken or misaligned. If the air is not purged within 2-3 minutes, turn the spa off, let the pump cool off, and try again. If so, remember to take the lid off next time before you refill it. When you turn on the motor, it will begin to rotate at a high speed.

In it, you'll get: The week's top questions and answers Important community announcements Questions that need answers see an example newsletter By subscribing, you agree to the privacy policy and terms HotTubandSpaExpert 64,122 views 3:42 Hot Spring Spa Not heating or no bubbles - Duration: 2:33. CAREFULLY reach inside the inlet with two fingers and see if the pump's impeller can be moved... Can't access the equipment?

In this picture we are using a large flat screw driver, some motors will require a 7/16 wrench. You want the water to drip from the fitting, maybe pour, but try to use one that will keep water away from the control pack and the back of the pump. Otherwise you will get more water than you bargained for. Inspect the pump wet end for evidence of corrosion of leakage.

Hope this saves somebody a service call! Why? This info can be found on the id sticker near the Sentry Control Box. are needed as you want to be able to remove the union whenever you need to service the pump.  Be sure not to remove or crimp the little o-ring inside the union,

Now that it is getting hot outside (upper 80's to lower 90's) the GFCI is tripping every day around the same time (3-3:30PM). First, have you just refilled your spa?