Home > Hot Tub > Hot Tub Motor Won't Start

Hot Tub Motor Won't Start

Contents

Try swapping it with one of your other circuit breakers that you know works. When water gets so low that the skimmer starts sucking air, this can cause the same effects of an air leak described above. enlarge 15. If the motor doesn’t work, turn the thermostat and timer completely clockwise. Source

Uncle Don Posted: 06/04/2016 7:32 AM Have Sta-Rite P6RA6G-207L. Close Yeah, keep it Undo Close This video is unavailable. Hopefully, with a bit elbow grease and maintenance you are now able to once again enjoy your hot tub trouble free for a long time to come. Broken Pump Impeller It's not usually the cause of a hot tub not working, but in rare cases of a broken spa pump impeller, the motor will start and sound fine, https://www.swimuniversity.com/troubleshoot-a-hot-tub-pump-and-motor/

Hot Tub Motor Won't Start

Inyopools Posted: 05/24/2016 15:58 PM Inyo Product Specialist buefordTJ - Your problem could be the 136VAC voltage. Why is で used here? To bleed air our of your system, first look for a drain plug on the pump and filter. If so, there is probably and Air Lock in the hot tub.

In most cases, wiring must be repaired or replaced or you may even need a brand new motor. If high speed turns on with either then swap wires on the motor because the low and high speed contacts are backwards. Popular Articles Basements Knowing When It's Time to Replace a Sump Knowing When It's Time to Replace a Sump Pump Electrical & Electronics Common Dryer Problems and Easy Ways to F Hot Tub Motor Hums But Won't Start This air pocket or air lock needs to be purged from the plumbing so the pump can function normally.

Thanks inyopools Posted: 07/08/2016 14:32 PM Inyo Product Specialist bt - This is typically the symptom of a wrong voltage problem. The pool pump was running but sounded loud. If your motor looks like this, get a new pump assembly (don't let the shaft seal leak for long or this is what your pump will look like). And when the pump is not pumping, nothing works, and the spa cools down.

A Spa Technician is here to assist: (800) 823-3638 Monday - Friday 6:00 AM to 5:00 PM Pacific Consumer Reviews EasyPak Spa Controls "It's just like the name No High Speed On Spa Pump Pump Seal Heater Manifold Valves Plumbing Jets Spa Shell All About Spa Packs Frequently Asked Spa Repair Questions Spa Anatomy Need help or additional information? Maybe the capacitor on the pump went out? Fourth, the mechanical switch in the back of the motor could be stuck in the high position, due to broken parts or insect infestation.

Hot Tub Circulation Pump Not Working

JIM D Posted: 08/17/2016 13:14 PM Motor is 1 year old. Visit Website Info for replacing a shift cable housing Why is looping over find's output bad practice? Hot Tub Motor Won't Start Bearings can be replaced, or if the motor is very old (more than 5 years old), you may consider replacing the hot tub motor. Hot Tub Pump Just Hums Sign in to add this to Watch Later Add to Loading playlists...

Fourth, it is possible that the breaker itself is in need of replacement. Useful Spa Repair & Diagnosis Tools The basic hand tools: screwdrivers, needle-nose pliers, wrenches, wire cutters, etc. DISCONNECT THE POWER AT THE GFCI SWITCH AND/OR THE MAIN PANEL CIRCUT BREAKER or FUSE BEFORE INSPECTING OR INSTALLING SPA PARTS. The voltage is 128v at each lead.I disconnected the ground lead and did a continuity check back to the breaker panel, sat. 2 Speed Spa Pump Troubleshooting

Checked the common problem, tripped circuit, etc. The start capacitor is in the back of the motor under the cap. Spa pump motor bearings can be replaced, a new motor can be installed, or installing an entire pump and motor will fix a noisy motor. Motor is Running but Nothing is Happening If you can hear the motor running but the water isn’t circulating properly, you could have a damaged motor or even an impeller.

Remove the mounting screws and put the pump on a bench. 9. Spa Pump Replacement Put hot tub in time clock mode. There is usually one on each side of the pump, to allow the pump or heater to be removed for service or replacement.

If water is dripping or spraying from where the union connects, the PVC threads may have shrunk (from running pump without water), or the threads may be loose and simply need

Chris Posted: 09/25/2016 13:26 PM Have Motor 855B Century 2Hpr, can turn on & off from the circuit breaker, but will not turn off or on from switch panel. What follows are some of the most common pump problems that arise when hot tub troubleshooting. If the power is correct here, then the terminal or cord is damaged. 2 Speed Spa Pump Wiring Diagram Same issue today.

Disconnect the plumbing from the the inlet and outlet. Something jamming the pump from turning? I read that air in the pump can prevent priming. Some spas have an air bleeder assembly after the pump, but for most spas, the most direct way is to loosen the union on top of the spa pump - just

In some cases slice valves can close by themselves, if they are loose and subject to heavy vibrations. I would recheck the wiring to and from the switch or possibly replace the switch. Does it hum or vibrate when you turn on your jets? But when he said the motor needed to be replaced, I didn't question.

This is due to the extra load the water puts on the impeller that we can't detect in the dry test. Happy Hot Tubbin’ Daniel Lara Hot Tub Works Tags: hot tub pump problems, hot tub pump trouble, spa pump problems, spa pump troubleshooting This entry was posted on Thursday, April If your question was not answered here, feel free to post a comment below, or call our helpful spa tech support personnel at  800-770-0292. Sometimes the system will automatically clear the problem with repeated manual attempts to prime the pump, while other times opening the main circulation pump union a bit and then closing it again

Hot Tub Maintenance: How to Winterize Your Hot Tub An essential part of hot tub maintenance is winterizing each summer. Common Problems Now that we all understand at least a little bit about how a pump actually works, let’s take a look at many of the most common problems you just A History of Swimming Pools Winter Pool Cover Reviews 3 of the World's Most Famous Extreme Pools Best Safety Cover for Inground Pools Categories Buyer's Guide Blog Posts Commercial Pool Blog Third, is something blocking the lines?

If the voltage is listed as 115VAC, the voltage should not exceed 127 VAC. As I indicated, it's probably 10 years old. Try a strong hosing first to remove debris. Q: My Spa Pump is On, but Barely Pumping A: First, check the spa filter, it may need cleaning.

Home Hot Tubs Inflatable Spas Cheap Spas Moderate Spas Under $3,000 Over $3,000 Luxury Spas Small Hot Tubs Dream Star 2 Person Tub Hot Tub Service Hot Tub Parts Hot Tub Without them, your spa would be nothing but an over-priced bathtub. In this case, the noise would not last more than a few minutes. Inyopools Posted: 06/21/2016 9:05 AM Inyo Product Specialist George - Yes, it sounds like you have a failing start capacitor.

Motor runs for 1 second after I shut the breaker off and then on. Sign in to make your opinion count. Had this configuration for the last 7 years. 1 2 3 Next Home How To Guides How To Determine Why a Motor Won't Start or Shuts Off Most Popular Swimming Pool