Home > Hot Tub > Hot Tub Display Not Working

Hot Tub Display Not Working

Contents

Hot tubs with these readouts will display an error code when something is wrong or malfunctioning. Anybody know what the issue might be???!!!! I hope it isn't though and I am going to try Chandler's suggestion of replacing that one breaker because it would certainly be the cheapest fix! Working... http://virtualthought.net/hot-tub/hot-tub-blower-not-working.html

It's usually an easy fix, when you have no power to the spa - the greater disappointment is not being able to use the spa at that moment. Perhaps a leak or fault in the jet motor or motor controller? I resoldered it and honestly it isn't a good thing to do I know. If it's not that breaker, I am pretty sure the whole motor needs replacing but it is a bear to take apart as the main connections to the water feeds are https://www.swimuniversity.com/5-common-hot-tub-issues-solutions/

Hot Tub Display Not Working

Pump 17 Spa leaks. I need to replace it but until it warms up here I can't risk a freeze. February 15th, 2016 by Daniel Lara It's a common spa question that we get asked all the time.

Just to humor me, however, shut them off and back on again anyway. If no, check the voltage at the pump. They are not usually repaired, unless you happen to be a electrical engineer. Hot Tub Not Heating Troubleshooting Solution: Check the connection or replace the sensor.

But, when dealing with water and electricity, it always provides a danger that must be respected. How To Fix A Hot Tub That Won't Turn On Solution: If the temperature of the water is actually 108° or hotter, the temp sensor should be replaced. It's almost always an easy fix, so don't worry that you have major problems, you probably don't. I appreciated the expert tech support you provided by phone, the new pack arrived promptly, and my spa is up and running again just like new.

KungFuMaintenance 36,415 views 8:34 How to Diagnose and Repair Your Hot Tub Heater | Arctic Spas - Duration: 9:09. Hot Tub Heater Reset Button Also look for loose or worn out jet seals and check the nozzles for obstructions Categories Accessories Chemicals Cover Removers Covers Filter Cartridges (Unicel) Filters Cartridges (PuraSpa Disposable) Fragrances Gift Ideas You must be logged in to post a comment. If your spa heater won't heat, remove your spa cartridge and clean the filter(s), to see if you have a pressure or flow rate problem.

How To Fix A Hot Tub That Won't Turn On

Heater element? try here Bought new filter, (this is when I found the gfci had tripped earlier in the week) I reset gfci put filter in and went to work. Hot Tub Display Not Working Each time they are cleaned, they lose a bit more of their ability to trap small dirt and contaminants. Hot Tub Pump Troubleshooting Two weeks ago i got out of the hot tub and my girlfriend unplugged a radio we put in the window and the radio flashed tripping the gfci tripped.

The first breaker is seeing the total amperage. http://virtualthought.net/hot-tub/master-spa-lights-not-working.html After bleeding, try turning the power on again and see if the jets work. You might turn each 240v breaker off and then on just to eliminate one more possibility. Most air leaks occur at the union in front of a pump, either loose or with a misaligned o-ring. Hot Tub Pump Wont Turn On

That would explain the two minutes then trip. 08-21-07,06:30 PM #14 ecman51 Banned. It can also be from loose wiring connections to the spa pack. All rights reserved. have a peek here This is one of those GFI outlets with the red test button, and a black reset button.

You can leave a response, or trackback from your own site. Hot Tub Control Panel Blank Filter Cartridge Pump 14 High-limit trips erratically; trips at end of heat cycle. Giving me a headache lol!

Sign in Share More Report Need to report the video?

On the board when power is on and one solid led light and one flashing led light that says "flash ok" next to it. if a GFCI is tripping and you do not know why it tripped you are placing the lives of anyone who gets into that tub in danger. The valves I speak of are usually "Slice" valves, also called Guillotine valve. Hot Tub Motor Won't Start COOL = Spa water is more than 20° F cooler than the temperature set point.

BigMike Okay I have an old hot tub. Symptom Components Associated Cure 1 Spa does not run, no power, nothing works. Davy Merino InTheSwim Blog Editor Posted in How To Pool Blog Posts Tagged Hot Tub Troubles, hot tubs, Spa Repair, spas permalink Post navigation ← Black Friday Pool Supply Clearance Check This Out Why do you think it isn't?There should be a 240v (2pole breaker) in the main box.

Daniel Lara Hottubworks.com Tags: Hot Tub Heaters, Spa Heater Elements This entry was posted on Thursday, March 7th, 2013 at 6:04 pm and is filed under spa heater. Close the incoming valves, and remove the spa pump unions.