Home > Hot Tub > Hot Tub Control Panel Blank

Hot Tub Control Panel Blank

Contents

About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! Please take all necessary precautions before attempting any repairs. Janis Cuthbertson first I cleaned the filters then I replaced them still says flo Matt Giovanisci You may need to call a professional to take a look at your pump. Touch Pad Is Working But My Blower, Pump Two, Pump One High Speed, Heater Or Light Is Not?You will have a central controller box that all these components plug into.Turn Power

Different from a jet, blowers cause gentle bubbling in the water to enhance the spa experience when used along with other features of the hot tub. Hope you find this post helpful, and if you have any additional questions, be sure to ask in the comments below. Be sure you have proper voltage to the control box from the house and that you also checked each fuse on the circuit board with a meter. Checked all the peripherals. http://www.doityourself.com/stry/troubleshooting-hot-tub-control-panel-problems

Hot Tub Control Panel Blank

The predominant manufacturers are Balboa, Gecko and Hydro Quip. I need to replace it but until it warms up here I can't risk a freeze. See complete list of error codes here. Sunplay Company ›About Us ›Blog ›Brands ›Our Utah Store ›Sponsorship Program Resources and Policies ›Image Copyright ›Pool Volume Calculator ›Privacy Policy ›Shipping Policy ›Terms & Conditions Sign up for emails Subscribe

To remove an air lock, loosen either fitting on the pump to allow the air in the pipe to escape – water should flow for about 5-10 seconds before retightening. 3. Open the cover and let the water cool off. If any of these symptoms are present, perform the following: Turn the power off and unplug the panel from the circuit board. Hot Tub Control Panel Locked Here's how to transport your paddleboard.

To do this, either turn the wheel or the screwdriver slot on the pressure switch counter-clockwise one full turn (two at the most). Top Side Control Panel Not Working Professional help is normally required if replacing the pump does not remedy the problem. Hottubspasupplies 54,361 views 2:33 How to Drain and Clean a Hot Tub - Duration: 8:43. hop over to this website If you don't confirm water is moving in the hot tub and through the heater do not proceed with the next step as in doing so may burn out the heating

Displaying Dashes If the control panel is not displaying an error message but only dashes, you need to reset it. Hot Tub Lights Not Working If it still does'nt work you may have a bad main control panel, bad connection at the PWA or a bad PWA. If the code did not go away then the circuit board will need to be replaced or sent in for repair. If there is any condensation, dry it out.

Top Side Control Panel Not Working

Derek January 14, 2014 Reply That did it!

Touch pad does not respond to touch: Check the panel has not been locked. Hot Tub Control Panel Blank Gear Backpacks Hydration Packs Life Jackets Water Bottles Carry your faves with you. No Display On Hot Tub Then try your main control panel button again.

Gecko Circuit Board: If you have three flashing dots on the display and there is a red light illuminated on the circuit board then the high limit sensor needs to be Unplug it from the circuit board. Check your owner’s manual for a complete list of error messages. Anyone else on this thread have any advice? Hot Tub Control Panel Codes

Similar to the Flo error, there are a number of other possible causes to this problem. Good luck! Loading... If so, the pressure switch or the pressure switch cable is defective and should be replaced.

Ask a Question or Comment Cancel reply Message *Name * Email * Phone Number * City * I agree to participate in this conversation via email. Hot Tub Control Panel Replacement Turn off the power for about an hour and then restore the power to the unit. See "error codes/blinking dots" above. 3.

If there is still a problem, turn off the breaker again, disconnect the control panel and examine the circuit board.

Most spas feature a temperature control on its topside control panel—typically one to raise up the temperature and one to lower it. Be sure the incoming power is coming from where it should. Learn More Nancy Anderson our water smells sour-we use chemicals, change the filter and the water often-what is this? Hot Tub Buttons Not Working You can see the little legs.

The manufacturer will not warrant this type of damage. Dirt, rust, or moisture will cause issues with your panel’s readout. Now it trips imediately when reset..Sounds like the heater is bad to me but more test tomorrow. Is my control panel toast?

Up next How to Find, Test and Replace Hot Tub Fuses | Arctic Spas - Duration: 3:28. I had looked at that ribbon cable several times before but didn't realize that was where they connected. And it seems to me it might be the problem after tracking every wire. stackz00 150,870 views 8:06 How to Fix an Air Lock in Your Spa : Pools & Spas - Duration: 3:08.

Wherever you are. It will need to be replaced. Do not use spa when temperature is flashing or the OH message is displayed. Check your connections to make sure that it’s secure and tight.

May need to get it replaced. Cheers Bobby Speeks October 02, 2015 Reply Just purchased a used Sundance spa an the display panel continues to blink…..I can turn the heat up an down, turn the light on…..but There also was a time where the pump was coming on and off all on it's own, sometimes several times / minute. The noise is definitely not coming from that or any of the other two pumps or the blower.

The first step is to simply reset the breaker. If you test the board and see it has low voltage, that is another sign you may need to replace the circuit board.