Home > Hot Tub > Hot Tub Blower Not Working

Hot Tub Blower Not Working

Contents

Also before upgrading to a larger pump, you should make sure your filter can handle the increased flow rate. But it's definitely getting worse. Do note, however, that some municipalities or other environmental authorities have strict regulations regarding the disposal of DE. By now u probably fixed it but I felt like answering because Matt's go to answer is call a professional. Source

If it resists just a little before stopping and you hear a "click, it was probably tripped. On the other hand, if you cannot get the heater to shut ‘off while the valves are open and the pump is running "dry", then the switch is either broken or Spa Pump Trouble F.A.Q. Turn the screw clockwise to raise the setting. check my blog

Hot Tub Blower Not Working

It came on for a few seconds then quit. I hope that this FAQ of Hot Tub pump problems has been helpful to you. Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. Pump 17 Spa leaks.

Pump Will Not Come On At All First, determine what voltage the pump you are troubleshooting requires to work. GFCI Heater Element Symptom Components Associated Cure 13 Reduced water flow. Two weeks ago i got out of the hot tub and my girlfriend unplugged a radio we put in the window and the radio flashed tripping the gfci tripped. Hot Tub Pump Troubleshooting Fourth - is the o-ring that seals up the impeller housing, or volute.

The impeller should glide on easily and turn onto the shaft easily until the threads bottom out with a very solid stop. Hot Tub Blower Works But No Bubbles Lot of learning on this project. Do not attempt to perform electrical repairs unless you are qualified. https://www.swimuniversity.com/5-common-hot-tub-issues-solutions/ If the wires have been removed, check it for continuity.

Otherwise, depending on how the heater is oriented, you may get water inside the control box and on your wiring. Hot Tub Pump Wont Turn On I don't want to buy a new blower motor if thats not the problem and I am hoping i will not have to dig up pipe to install a loop either. If something is broken inside the motor, it doesn't take long (at 3400 rpm) for broken spa pump parts to be worn down to nothing. If you have two pumps, chances are it's one or the other - either your jets don't work, or the spa circulation isn't working.

Hot Tub Blower Works But No Bubbles

If insulated properly you should not be able to see the side of either bulb under the cap once the nut is tight. http://www.doityourself.com/stry/troubleshooting-hot-tub-blower-problems Bought new filter, (this is when I found the gfci had tripped earlier in the week) I reset gfci put filter in and went to work. Hot Tub Blower Not Working I interchanged them and there was no change, i.e. No Power To Hot Tub The arcing has an affect on the cycles (usually 60Hz) and can change them.

My spa has some warm air space around the foam which apparently is drawn into the air lines by the blower.What's a "relay" look like? this contact form Bri M I went to clean hot tub today. Check wiring inside to be sure nothing came off. Checking Your GFCI Switch The GFCI is a current breaker in your hot tub. My Hot Tub Won't Turn On

One of the advantages of DE is that it's organic and non-polluting. You can switch fuses to see if it is blown but you might blow another so you need one anyway. Tell us by commenting below! have a peek here Leave a Reply Click here to cancel reply.

Is the thermostat set properly? Hot Tub Display Not Working This could be due to high amperage (such as in a heater) or due to a GFCI protected circuit needing control over a non-GFCI protected circuit. Flow/Pressure Switch Thermostat Heater Contactor/Relay Heater Element Spa Side Control Filter Cartridge 3 Excessive heat.

My filter after two days was really dirty I guess from rain and no cover.

Close Yeah, keep it Undo Close This video is unavailable. Do you have a meter?Check and see if the plug on the blower is in tight and the pins are making contact.I would open the box, look to see if there If wiring inside is OK, the air switch may be faulty. Hot Tub Motor Won't Start The only way the low speed pump should come on without the use of the timer (if the pack is fresh out of the box) is if the installer happens to

Brooke There seems to be a really loud noise coming from my heat element that with in the last few days is getting louder and louder. Heater Problems Heater Failure - Due to Water Flow Are the ball valves open? If you have any questions, do not hesitate to check with your local retailer, service technician or supplier for assistance! Check This Out Remove filter cartridge and recheck heater with amp meter. (120v should read 12.5 amps; 240v should read 25 amps, however this may vary on specific spa models - check your instruction

Results 1 to 15 of 15 Thread: No more bubbles out of the spa jets Thread Tools Show Printable Version Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode You will not need a tool to hold the impeller to check tightness. Scrub the walls and tiles with appropriate brush and cleaner. Hot Tub Troubleshooting: Heater Problems Let's get to the source of your hot tub heater problems with this handy guide. 5 Tips for a Clean Hot Tub Filter Keeping your hot

Damaged O-ring. It seems very odd that when you drained the water to a lower level the jets would blow but when the water level was raised back up it would stop blowing. Water imbalance. If the jets were pretty strong before with the old 3/4 HP separate pump, then they were probably 3/8", otherwise they might be 7/16" if they felt more on the weak

Hot Tub Blogs should do this more often - These are our most Frequently Asked Questions about spa pump repair. Mechanical thermostats are prone to calibration swings due to changes in the temperature around the switch body, capillary tube, and sensing bulb. Most are 6kw and are rated for 240 volts. I'm going to try blowing out the lines next.

Most now have electronic temperature controls (called a Thermistor) available with the spa-side control heads. If it measures higher, the motor will prematurely burn up. As a "rule of thumb', always check the motor shaft for free movement after applying the impeller to the shaft and after assembling the face of the pump. Check that the valve in front of the pump are open, and that nothing is clogged in the suction lines, including the spa filter.

If debris has gone through the pump, some of it may be stuck in the blades which will reduce the effectiveness of the pump. Try using a hair dryer on these components. He should stop being so helpful. Spas and hot tubs with one pump usually have a 2-speed motor, operating on low speed most of the time, and on high speed when using the tub with the jets.

Dry-rotted, out of position, or possibly loose, along with loose screws around the face of the pump. If no voltage is found, adjust calibration on the thermostat by turning Allen screw at top of switch clockwise until a "click" is heard or you reach 1/4 revolution (whichever comes Is the pump flood primed?